Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
It is recommended to avoid printing the first layer too close to the build plate as this might cause the material to over-adhere. As a result printed parts can be difficult to remove when printing with this material
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
Parts show a small amount of warp, a brim is recommended for large and complex parts. Parts do not self-release, however do not require much effort to remove with a part removal too Parts warp after removal from build plate, most probably due to build-u
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. A brim is recommended when printing with this material
A brim is recommended when printing this material with Magigoo Original, it is also recommended to increase the build-plate temperature slightly if the printed parts are warping
CC 0.6
Ultimaker S5
Metal
BASF Ultrafuse 316L
100
100
245
245
Recommended
https://magigoo.com/blog/ultrafuse-316l/
Applying water around the printed parts through the use of a spray or wash bottle to the build-plate and letting it sit for 30 minutes to 2 hours is required for part removal. It is also recommended not to print too close to the build-plate on the first layer. When using the Ultimaker S5, one can reduce the first layer flow to around 85% to aid with ease of part removal
0.6
BCN3D SigmaX R19
Metal
100
100
240
240
Recommended
https://magigoo.com/blog/ultrafuse-316l/
Applying water around the printed parts through the use of a spray or wash bottle to the build-plate and letting it sit for 30 minutes to 2 hours is required for part removal. It is also recommended not to print too close to the build-plate on the first layer.
It is recommended to print with the first layer build-plate temperature set to around 80-100 °C cooling the build-plate to around 20-70 °C. It is also recommended to use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
For best results ensure that the filament is dry before printing. It is recommended to use Magigoo PC with Innofil ASA for optimum adhesion. Parts self-detach from the build-plate on cooling.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo Original
It is recommended to print with the first layer build-plate temperature set to around 80-100 °C cooling the build-plate to around 20-70 °C. It is also recommended to use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
Use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
Magigoo PP is the optimum build-plate adhesive for this material. Parts should be easy to remove off the build-plate on cooling. In case of excess adhesion it is recommended to heat the build-plate up to °C to make part removal easier.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo Flex.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended for larger parts or complex geometries when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended for larger parts or complex geometries when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
A brim is recommended when printing this material with Magigoo Original, it is also recommended to increase the build-plate temperature slightly if the printed parts are warping
A brim is recommended when printing this material with Magigoo Original, it is also recommended to increase the build-plate temperature slightly if the printed parts are warping
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. Most parts can be printed without the need for a brim
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
For best results ensure that the filament is dry before printing. It is recommended to use Magigoo Original for optimum adhesion. Parts self-detach from the build-plate on cooling.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Magigoo Original gives a balance of good adhesion and easy release with this material, nonetheless the Material Manufacturer suggests using Magigoo PC if extra adhesion is needed. Caution: Using Magigoo PC with ABS materials increases the chance of damaging glass build surfaces
Magigoo Original gives a balance of good adhesion and easy release with this material, nonetheless the Material Manufacturer suggests using Magigoo PC if extra adhesion is needed. Caution: Using Magigoo PC with ABS materials increases the chance of damaging glass build surfaces
When printing this material in a heated chamber a brim might not be required, furthermore the higher environmental temperature helps prevent delamination in larger parts.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
For best results ensure that the filament is dry before printing. It is recommended to use Magigoo PC with Fillamentum ASA for optimum adhesion, nonetheless Magigoo Original works well form smaller sized parts.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PP.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
A brim is not required when printing this material with Magigoo Original, it is also recommended to increase the build-plate temperature slightly if the printed parts are warping
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. A brim is recommended when printing with this material
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. A brim is recommended when printing with this material
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
AA 0.4
Ultimaker S5
Custom
Igus
110
110
20
260
260
A brim is recommended when printing this material.
0.4 mm
Intamsys FUNMAT HT
HT
280
280
Recommended
Filament tested to show very good adhesion at build-plate temperatures in the range of 100-160 °C with Magigoo HT
0.4 mm
Intamsys FUNMAT HT
HT
160
160
280
280
Printing with an enclosed chamber is not recommended if there is no active extruder cooling. Filament tested to show very good adhesion at build-plate temperatures in the range of 100 - 160 °C with Magigoo HT
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
Magigoo HT is recommended when printing this material due to its higher temperature requirements. A brim is recommended when printing with this material.
Magigoo HT is recommended when printing this material due to its higher temperature requirements. A brim is recommended when printing with this material.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
A brim is necessary when printing this material, Magigoo PP is recommended to ensure easy part removal with this material. It is also recommended to lower the first layer printing speed to improve first layer adhesion
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
A brim is necessary when printing this material, Magigoo PP is recommended to ensure easy part removal with this material. It is also recommended to lower the first layer printing speed to improve first layer adhesion
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
AA 0.4
Ultimaker S5
PC
Mitsubishi Durabio
110
100
7
260
260
Recommended
For best results ensure that the filament is dry before printing. It is recommended to use Magigoo PC for optimum adhesion. Fan speed can be changed to 0% is the model is warping
AA 0.4
Ultimaker S5
PC
Mitsubishi 3Diakon
100
100
7
260
260
Recommended
For best results ensure that the filament is dry before printing. It is recommended to use Magigoo PC for optimum adhesion. Fan speed can be changed to 0% is the model is warping
It is recommended to print with the first layer build-plate temperature set to around 80-100 °C cooling the build-plate to around 20-70 °C. It is also recommended to use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
It is recommended to print with the first layer build-plate temperature set to around 80-100 °C cooling the build-plate to around 20-70 °C. It is also recommended to use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
It is recommended to print with the first layer build-plate temperature set to around 80-100 °C cooling the build-plate to around 20-70 °C. It is also recommended to use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Use a slow first layer printing speed (< 20 mm/s) and a wide brim to help mitigate warp further. In the case of larger sized parts, part removal might require more effort, in this case it is recommended to heat up the build-plate to around 80 °C to help with part removal
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
A brim is generally not required when printing with this material and Magigoo PC on the Ultimaker S5. Parts are easy to remove once the bed cools down. Polymaker recommend and enclosure for larger sized parts
A brim is generally not required when printing with this material and Magigoo PC on the Ultimaker S5. Parts are easy to remove once the bed cools down. Polymaker recommend and enclosure for larger sized parts
A brim is generally not required when printing with this material and Magigoo PC on the Ultimaker S5. Parts are easy to remove once the bed cools down. Polymaker recommend and enclosure for larger sized parts
A brim is generally not required when printing with this material and Magigoo PC on the Ultimaker S5. Parts are easy to remove once the bed cools down. Polymaker recommend and enclosure for larger sized parts
A brim is generally not required when printing with this material and Magigoo PC on the Ultimaker S5. Parts are easy to remove once the bed cools down. Polymaker recommend and enclosure for larger sized parts
Prints well when using Magigoo Original, an enclosure can help with first layer adhesion and inter-layer adhesion especially for larger sized parts. Most parts can be printed without the need for a brim
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
A brim is recommended when printing with this material and Magigoo PC on the Raise3D N2. Parts are easy to remove once the bed cools down. Polymaker recommends and enclosure for larger parts
A brim is recommended when printing with this material and Magigoo PC on the Raise3D N2. Parts are easy to remove once the bed cools down. Polymaker recommends and enclosure for larger parts
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. A brim is recommended when printing with this material
Prints well when using Magigoo Original, an enclosure can help with first layer adhesion and inter-layer adhesion especially for larger sized parts. Most parts can be printed without the need for a brim
Prints well when using Magigoo Original, an enclosure is recommended to help first layer adhesion and inter-layer adhesion especially for larger sized parts. A brim is recommended when printing with this material
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo Original
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is recommended when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is required when printing this material
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PA.
It is recommended to avoid printing the first layer too close to the build plate as this might cause the material to over-adhere. As a result printed parts can be difficult to remove when printing with this material
A brim is recommended when printing this material with Magigoo Original, it is also recommended to increase the build-plate temperature slightly if the printed parts are warping
Applying some water around the printed parts through the use of a spray or wash bottle to the build-plate and letting it sit for 5 minutes makes part removal significantly easier and is recommended for larger parts.
Filament should be kept in a dry place and it is suggested to dry filament prior to printing for optimum printing results. A brim is not required when printing this material with Magigoo PC.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.
A brim is recommended when printing with this filament and Magigoo PP. Parts become easy to remove once the build-plate cools. It is recommended to first pry the brim around the part before attempting to remove the whole part.